WPA CO 8000 Uživatelský manuál Strana 1

802.11a/b/g Wireless LAN Outdoor AP WAP-8000 User’s Manual Version 1.0

4. Locate an optimum location and use the provided Mounting kit to tie the WAP-8000 to a pole. Step3 Step2 Step1 Note: For secured reason, while

! TDOOR INSTALLATION WARNING IMPORTANT SAFETY PRECAUTIONS: LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions th

z Refer to the National Electrical Code for grounding details. IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND CANNOT MOVE: z DON’T TOUCH TH

Chapter 3 Web configuration Web configuration provides a user-friendly graphical user interface (web pages) to manage your WAP-8000. An AP with an a

Assign a static IP address If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps bel

Chapter 4 Status This page shows the current status and some basic settings of the device, includes system information, wireless Configuration and sec

Wireless Information Parameter Description Mode It shows wireless operation mode. ESSID It shows the SSID of this WAP-8000. The SSID is the uniqu

Chapter 5 Network 5.1 Wireless Settings This page allows you set wireless relative parameters for your wireless network. Parameter Description Mo

5.2 IP Settings This page allows you Setting IP address information. Device IP Parameter Description DHCP Client Getting the IP address from DHCP

5.3 Antenna Settings This page allows you selecting antennas for transmission. For WAP-8000 model, it only supports one antenna connector, please sinc

Copyright Copyright© 2009 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribe

Chapter 6 Device 6.1 Bandwidth This page allows you limit the total upload or download stream. Be noticed, it’s only available in AP Client mode.

6.3 Device Reboot This page allows you reboot WAP-8000. 6.4 Backup / Restore This page allows you backup or restore the configuration file you’ve sa

6.5 Hostname This page allows you modify the name of WAP-8000. 22

Chapter 7 Security 7.1 Access Control Via wireless MAC addresses control, you can set certain wireless client for accept or deny accessing WAP-8000.

7.3 Password Settings The password of the user interface can be changed here. Please enter the new password and confirm the new password, then press “

Chapter 8 Localization 8.1 NTP Settings This page is used to configure NTP client to get current time. 8.2 Country Code Settings The country code c

Effective use of the radio spectrum – Article 3.2 Testing for radio test suites according to EN 300 328-2 has been conducted. These are considered rel

TABLE OF CONTENTS CHAPTER 1 INTRODUCTION...5 1

Chapter 1 Introduction The WAP-8000 is an outdoor 802.11a/b/g Outdoor wireless AP with N-type antenna connector. This manual describes the details of

1.3 Specification Standard support IEEE802.11b/g IEEE802.3/u Interface Wireless IEEE802.11a/b/g LAN: 1x 10/100BaseTX, Auto-MDI/MDIX Data Rate 802.

802.11a/g: 54Mpbs (64QAM): -66dbm 48Mbps (64QAM): -71dbm 36Mpbs (16QAM): -78dbm 24Mbps (16QAM): -80dbm 18Mbps (QPSK): -81dbm 12Mpbs (QPSK): -82dbm 9Mb

Chapter 2 Hardware Installation 2.1 Outlook 1. On the back panel of WAP-8000, there are LEDs indication (LAN, WLAN, PWR). 2. On the bottom of

2.2 Hardware Installation Before you proceed with the installation, it is necessary that you have enough information about WAP-8000. 1. Plug in the w